Reasons Your fiat punto key 500 Key Fob Won't Work

A fiat 500 car key replacement 500 key fob makes it easy to open doors and start your vehicle. There are a myriad of reasons why the key fob might stop working. This includes a dead battery water damage, receiver modules issues, and interference.

This listing is for a NEW replacement key for fiat 500 fiat punto key fob replacement Flip Key Remote - similar to the Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). Includes lock, unlock and trunk buttons.

Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not working. Modern key fobs come with a limited operating range, and must be within a few feet of the vehicle to operate. If you are further away from your vehicle and you hit the keyfob, it will not respond, and display the message "Key Fob Not Detected".

If this happens, replace the battery of your coin cell (Part number CR2032) with a new one from a reliable brand such as Panasonic, Duracell, or Energizer. You can find them at your local hardware store, or online.

After you've replaced the coin cell battery, you can test it by standing near your fiat keys 500 and pressing the buttons. The parking lights should blink and the key fob should operate the lock and unlock switch.

If the key fob won't work after replacing the battery, it could have water damage that stops it from communicating with the receiver module inside your vehicle. Water damage can happen through a variety of methods, including an easy splash or submerging the key fob into saltwater at the beach. If you suspect that your fob has been exposed to water, you can place it in a bag of rice to draw out the moisture. If this doesn't work, you will need where to get a fiat key cut; please click the up coming post, have your fob replaced by an auto locksmith or a dealer.

Water Damage

Water damage can occur if you immerse the fob into the ocean, or wash it in a washer. Saltwater can cause the circuit board to short, and eventually fail. It's not good to let the fob get wet, but don't give it up if you accidentally drop it in the water or don't take it out of your pocket.

Take the battery off first. Before replacing the battery, clean the electronic chip using isopropyl or similar products. Then test the fob to check if it functions. If the key isn't working, it may need to be reset. This is usually done by an auto locksmith or dealer.

If the key you have is older and has not been programmed to work with your vehicle it is necessary to replace it completely. This is a simple process which can be accomplished by a professional automotive locksmith. The locksmith will need to cut the key to match the ignition of your car. The locksmith will also need to program your fob into the vehicle's system. This is a cheap and quick process that could be completed in the same day.

Receiver Module Issues

One of the main reasons why your 500 key fob may stop working is that it's simply out of range. The remote usually has 30 feet of range or less, and if it's too far away from your car it won't respond to your commands. This can easily be resolved by moving it closer to your vehicle until it begins responding.

If your fob won't work after you replace the battery inside the coin, which is also known as a "button", "watch" or "button", it could be a problem with the internal circuit board. Reprogramming your fob can resolve this issue. The instructions are available for the majority of vehicles on YouTube or in the owner's guide.

It is sometimes necessary to replace the clips made of metal that hold the coin batteries in their place. If they loose tension, it could prevent the coin battery from being properly seated, and this will cause the remote to malfunction.

In rare cases it is possible that the fob will become disconnected from your vehicle due to software problems or hardware issues. This can be a major problem, but you can usually resolve this issue by visiting an auto locksmith to have them reprogram your fob. In some instances the software may require reinstallation in your body control modules.

Interference

In addition to a dead battery on a coin The key fob may not be able to transmit or receive an signal due to interference. This could happen if the key fob is near radio transmitters (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob might not work because of a weak connection with the buttons, water damage or damage to the internal chips.

If the key fob failed to work one day without notice, or after trying everything you can at home to fix it e.g. replacing the battery, reprogramming, and using the spare key fob, you may have a malfunctioning receiver module on your 500. The receiver module is located under the dash and receives the radio frequency signals from the key fob. It converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy method of resetting all on-board systems in your 500 device, including the key fob. Disconnect the 12 volt battery for about 15 minutes, by disconnecting the negative cable first then the positive cable. Reconnect the battery. This will eliminate any remaining electricity and then restart the car's computers. This can help the key fob to function again. If the problem persists you should seek out an expert technician. They can identify the exact cause of any issues.