How to Repair Bifold Door Top Roller Guide

If your bifold door is squeaking, it's likely that they require some maintenance. You may have to clean, lubricate or adjust them. The problem may be caused by loose screws on the top pivot or by the top guide roller.

This kit includes all the necessary hardware to restore your bi fold door repair-fold closet door to its optimal performance.

Remove the Door

It may seem complicated and difficult to install a set of bifold internal doors, but for DIYers with a little experience, it is actually quite simple. The frame isn't the issue however getting the doors to fold and close smoothly is. As bifold doors are complex machines, they could require some tweaking to ensure they are functioning properly. This could be as simple as tightening a screw or as complex as removing the door and replacing the pivot pin or roller.

The majority of the time you can resolve these issues with a couple of simple adjustments, without having to remove the doors. You may find that your bifold doors are sagging and scraping the floor or bouncing off the track. Getting these issues under control isn't a big deal, and with three simple steps your bifold doors can be back on track in no time.

The most common problem that internal bifolding doors encounter is that they slide out of alignment. This can be caused by loose screws or holes in the anchor/pivot pins or simply a door that is not aligned. In most cases, you can correct this by making a few simple adjustments, however if the door isn't moving, it could be necessary to have it removed and replaced.

To remove the door you'll need an appropriate screwdriver, and possibly pliers (to assist in loosening any tight pivot pins). The screwdriver is used to disengage the locking levers at the bottom bracket for pivots. The pliers are used for removing the pin.

After the top roller is removed, you can lift the door, then swivel it downwards and remove it from its pivot brackets and track. It's usually a simple process, but you must be cautious not to let the door hit the frame of the door. Then, you can sand down the edges of the door to smooth it. You can then repaint it or refinish it as required.

Remove the Roller Guide

This spring-loaded roller guides mounts on top of bifolding doors to facilitate smooth operation. It is specifically designed for Kenna frames and will fit door panels from 1 inch to 1-3/8 inch thick. It is constructed of nylon, steel and plastic components. It will replace a damaged guide.

Remove any screws holding the roller guide in place with a screwdriver. Then, carefully use your hands to lift it out of the frame. It could require some effort to lift the door, so ask someone else to assist you.

After removing the guide, carefully cut off the remaining finish on the foot of the guide using a razor to separate it from blank rod. This will make the guide's foot much easier to remove and also prevent any damage. The guide foot is extremely sharp, and it can cut or snag fingers.

You may need to apply some force to remove the guide, but you must be careful not to break or chip the foot. After you've removed the guide from the rod blank, be sure to get rid of all the threads and epoxy that remain in the place where it was attached. This will help prevent any future problems with the guide.

After you have removed the previous guide, test your replacement by placing it at its new location. Make a few turns using masking tape or guide tubing to ensure it stays in place. This allows you to check the alignment of the guide and spacing to ensure everything is in place. It doesn't matter if you're looking at it from a distance or using the dependable CRB Spine Finder and Deflection System it is essential to avoid any problems in the future.

The final step is to replace the door. If the guide is in the correct position and functions just as it should, you can proceed. Make sure that any screws or pins that were removed or loosening should be replaced and tightened correctly when you're finished.

Remove the Bottom Pivot

Bifold doors make a gorgeous addition to any home but sometimes they require some adjustment or tweaking to stay in great shape. Some issues can be addressed with the doors in place. Others will require the doors be removed. This guide will show you how to take off the internal bifold door pins, rollers, and pivots.

The first step is to gather your tools. Putting everything together before time can make it easier later on in the project. You'll require a screwdriver, pliers and perhaps a wrench. You can buy a set of basic tools at your local hardware store at a reasonable price. It's also a good idea to keep some wood glue in your kit. This can be very useful when you need to glue one of the rollers back into their original position.

Once you've gathered your tools, start by opening the bifold doors, and then loosening the top track bracket using your screwdriver. Once the bracket is loose, the door should be able to slide off the top track completely. It might take a bit of shaking to get it there, but it should come off the track.

The bottom pivot of the frame needs to be removed. It is best to do this from the outside of your home, so be sure to close any interior doors that you are able to open. This will make it simpler than trying to work inside. If the track at the bottom is still in good working order you'll be able to simply lift the bi folding door repair and remove the track.

You'll have to replace the track if it is damaged. You can get new tracks for bifold repairs near me doors as well as swinging closet doors at your local hardware store. If the track is badly damaged, you may have to replace it entirely.

You'll need to test your doors for proper function. Make sure that they are easily able to move from position to position. You should also ensure that the edges of the door are parallel to the frame when closed. If they're not, you'll have to adjust the top pivot bracket and tighten or loosen the bottom set screw until the door's edge coincides perfectly with the frame.

Replace the Roller

Bifold doors can be used to neatly cover closets, laundry nooks and pantries, but only if they function properly. They are made up of two panels that are hinged and open using the track that is located at the top of the frame. Over time, the roller guides can wear out and cause the doors to sag. Replacing the roller guide requires only a few minutes, and the most basic tools.

The first step is to take the guide roller from the door panel. The pivot bolt at the bottom must be removed and the screw that holds the guide to the top of the door panel needs to be removed. After the guide is removed and the door panel is lifted up and away from its track. Then, loosen the bolt that holds the top pivot bolt and employ a wrench to pull it out of the hole in the top header of the door frame.

Stanley, Cox and Acme offer a replacement top nylon roller with a 7/8-inch diameter wheel on a steel base. It can be mounted on the top edge of bifold repairs near me doors that range from 1 inch to 1-3/8 inches thick. It is spring loaded to self-adjust the upper track to ensure smooth gliding.

Another issue that is common to a bifold doors repair door is that it scrapes the floor when it closes or opens. This can occur after adding carpet or other flooring materials that require the doors to be raised for proper clearance. Removing the bottom pivot adjustment screw and loosening the top track's mounting screws and moving the anchor pin usually enough to clear this issue.

A set top roller with new guides could be a low-cost solution to the problem of your bifold doors being difficult to operate. They're usually available at the hardware store near you in the door section, but they're also accessible online from a number of suppliers. In addition to a brand-new top roller guide, you will need a small container of Elmer's wood glue which is sold in the big box stores as well as a squeeze clamp. The clamp assists in keeping the repair area in place after glue is inserted, and allowed to dry.